Does composite decking need maintenance?
It's true that many composite decking options require very little maintenance but they do need basic cleaning in order to keep them looking presentable No, you don't need to repaint or reseal composite decking, and it is very resistant to rot, however, it's a good idea to sweep them clean weekly in order to prevent the growth of mold and lichen.
Is composite decking slippery when wet?
Composite decks are not slippery even when there is water on the surface. The problem, however, is when there is an accumulation of both ice and water on your composite decking. Aside from being the cause of accidents, ice, and the removal of it, can cause some damage to your patio. Non-anti slippery composite decking.
Is composite wood waterproof?
Composite decking does not absorb water. When moisture gets trapped under the decking and on top of the wood joists, it stays there and keeps it from drying properly. Homeowners who are looking for waterproof composite decking materials should look for those that have special features.
Why is composite wood so expensive?
Most composite decks are manufactured from the by-products of wood such as wood chips, sawdust, and recycled plastic materials.
This unique combination makes composite decks expensive than other types of decking material.
How much does composite wood cost?
Averaging between $3.50 and $6.00 per linear foot, the cost of installing a high-quality composite deck will certainly be higher than building with traditional pressure treated lumber, which can cost between $5.00 - $7.00 per (8') board.
What are the disadvantages of composite decking?
A pricey alternative to wood. Durability comes at a cost, as composite decking is more expensive than wood.
Composites aren't natural.
Composite decks aren't completely maintenance free.
You'll need to comparison shop.
Cons of Composite Decking
What are the problems with composite decking?
One of the most common complaints about composite decking is mold. Decking that is in shaded area or areas that tend to get wet frequently have been shown to grow mold and stain the deck. This is not restricted to composite decking. Wood decking can grow mold, mildew and algae.
How long do Composite decks last?
Composite decking can last over 20 years with the proper care and maintenance. Composite holds up better under hot or cold weather shifts. Composite is resistant to rot, mold, and termites, which can take their toll on wood decking materials. Composite does not require as much upkeep as wood.
20 years
  • Why is composite wood so expensive?
  • How much does composite wood cost?
  • What are the disadvantages of composite decking? Cons of Composite Decking
  • What are the problems with composite decking?
  • How long do Composite decks last? 20 years
Stripped screws are screws with damaged heads, making them almost impossible to remove by using […]

Stripped screws are screws with damaged heads, making them almost impossible to remove by using […]

Stripped screws are screws with damaged heads, making them almost impossible to remove by using screwdrivers. You may accidentally strip the screws by using the wrong drill bits. When installing new composite decking boards or replacing old ones, you may have encountered some stripped screws. So, how do you remove deck boards with stripped screws? If you want to take out the screws, here are some ways you can do it. 

Using Pliers and Vice Grips

One of the first things you’ll want to try when removing stripped screws is to remove them manually. To do this, you will need some locking pliers or vice grips. For this to work, the screw heads should also not be flushed deep into the wood. You will need to be able to grip the screw heads. If not, you may want to try other methods. 

For this method, grab some pliers or vice grips, preferably locking ones. Then, grip the screw heads with pliers and gently back the screws by rotating the pliers counter-clockwise. You may need to put in a little effort when dealing with rusting screws. Alternatively, you can apply lubricants to the screw’s shaft to loosen it. 

Using a Power Drill

As previously mentioned, the usual methods of backing the screws won’t work with stripped screws. However, there are still a few tricks and tips that you can use using a power drill. One trick you can use is by using rubber. 

For this method, you’ll need a small rubber piece that can fully cover the screw heads. A rubber band can do the trick. You can start by placing the rubber band on top of the screw head. It shouldn’t be too thin to get damaged by the drill bit nor too thick that you can’t place the drill bit into the screw heads. Then, with the right drill bit, slowly drill the screw head with the rubber in reverse. Once loosened, you can continue to back the screws out using this method or using pliers. 

Another trick is by using a lockable drill chuck. However, as with pliers and grips, it only works on exposed screw heads. You can put the drill chuck over the screw and tighten it until it grips the screw. Finally, set the drill in reverse to back it. 

Using a Screw Extractor Set

Another quick and effortless method of removing stripped screws is by using screw extractor sets. There are several varieties of these kits on the market. And each one may work differently than others. 

One of the most popular screw extractor sets you can buy are these special drill bits. The drill bits have two different ends. One end features a cutter side that drills a hole into the screw head. The other one is a reverse-threaded drill bit that bites on the drilled hole that the other end makes.

To use this type of screw extractor set, you will need to choose the right drill bit size first. Fortunately, they come in different sizes and as a complete set. Next, using the cutter side, drill a hole into the screw head. Then, with the threaded-size, drive the screw in reverse, backing it out in the process. 

As mentioned, there are several varieties of screw extractor sets available. You only have to find the right one that suits you best. You can use forums, review sites, and customer feedback when buying a set of these kits. 

Using A Pry Tool

remove decking boards with striiped screws

If all the other methods fail, there are a few more things that you can try. However, they most likely will damage the decking boards. Because of this, only try these as a last resort. To pry the decking boards, you can use a hammer or other prying tool. Using the claw side, slowly lift the boards upward. A slow rocking motion can help minimize damage. 

In some instances, prying the decking boards may leave the screws into the joists. If so, you can use pliers to unscrew them manually. If that doesn’t work, you can also cut the screws using a reciprocating saw.

Cutting the Decking Boards

To make prying easier, you can also opt to cut the decking boards into sections. Doing so reduces the boards’ resistance when prying them out. However, you will need to be careful not to cut through the deck frame. For this reason, you may need to familiarize yourself with your deck. 

Another method is by using plug cutters. Plug cutters are special drill bits that cut holes into decking boards. For this method, you will need a plug cutter slightly larger than the screw heads. Using the plug cutter, make a hole around the screws. After doing so, you can lift the decking boards out effortlessly. As for the screws, you can use the previously mentioned methods to remove them. 


Read full article on Ultra decking


Not All Synthetic Decking Is "Composite".
Not All Building Codes Allow Composite Decking.
Composite Lumber Is Not Just Decking.
Composite Lumber Can Be Expensive.
Higher-Quality Products Look More Like Wood.
Composites Can Be Slippery When Wet.